Fields with asterisks* are required. Your friend will receive an email that contains a reference to this page. Please send this email only to people you know who would be interested in this information.
All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures according to ISO 4254-13.
Arrives for quick and easy set-up. Minimal time wasted setting or prepping the unit.
7 Year gearbox warranty
Shows confidence in gearbox integrity.
Rugged heavy built gearboxes
Capable of handling heavy cutting applications.
Gearbox seal protection
Gearbox bottom seal protection for longer bearing life.
Sliding guard for splitter gearbox
Sliding guard offers protection and easy access for improved efficiency of splitter gearbox maintenance.
2 Piece drive-line shields
Drive-line grease zerks are easier to access.
Low hitch weight on tractor tongue
Ideal for smaller hp tractors by reducing the amount of weight on the drawbar.
Narrow A-frame hitch
Allows for a tighter turning radius.
Adjustable park jack angle
Park jack can be adjusted to be perpendicular to the ground.
Adjustable drive-line hanger
Serves as support rest for the drive-line when the cutter is unhooked from the tractor. Assist operator when attaching drive-line to tractor power take-off shaft.
Input drive-line: Cat. 6 CV
Drive-line is matched just right for tractor capacity. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the drive-line.
Drive-lines with slip-clutches: Cat. 4 intermediate Cat. 4 or Cat. 5 wing
Drive-line is sized right for the intended cutting capacity. Slip-clutches will slip under load to minimize twist damage to drive-line profiles.
Grease zerks on end caps of drive-line
Intermediate and wing drive-line cross journals are easier to grease.
High blade tip speed
Allows clean cutting of material.
6" Blade overlap
Eliminates skipping during turns.
Diamond blade bar
Provides the critical strength needed for consistent, top performance.
3/16" Round stump jumper
Standard thick stump jumper material keeps damage to a minimum.
Smooth top design
Reduces accumulation of debris and is easier and faster to clean.
Tops of decks are 100% welded
Makes center deck and wing deck stronger.
1/4" Sidewall thickness
Increased thickness reduces damage from objects being thrown into deck sidewalls.
Multiple center skid shoe locations
Run two or four skid shoes in locations under the tongue pivots or out at the wing hinges.
Beveled skid shoes on wing and weight box
Reduces gouging the ground when turning.
LED signal lights
LED lights are bright, long lasting, and resist vibration, unlike incandescent lights.
Hinged wing sections
Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting.
1" Solid hinge rods
Larger diameter hinge rod provides greater strength in the hinge area.
Wing transport lock pin
Transport lock pin will hold wing in folded position in the event of hydraulic loss.
Enclosed dual 1" leveling rods
Cutter pulls equally on the rear axle while traveling over rough terrain.
5-Bolt hubs makes the wheel assembly more durable and longer lasting.
Drain holes in wheel rims
Allows water to drain from wheels mounted on folded-up wing. Helps prevent paint deterioration and rusting to the wheel rims.
Spring cushioned center-axle
Protects unit from bumps and ground shock.
Optional spring cushioned wing-axle
Further improves ride over a multitude of terrains.
Replaceable individual wheel spindles
Spindles can be replaced when damaged without replacing entire axle assembly.
Laminated tires: Eliminates flats. Air-filled tires: Give better cushion while transporting. Foam-filled tires: Give better cushion while transporting and can't go flat.
LP Performance hitch option
Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar up to 12 degrees in both left and right directions.
Bar-tite hitch option
Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.
Maintenance free tongue & axle pivots
Self lubricating journal bearings make for less maintenance.
Color coded hydraulic hose handles
Easy hose identification & sturdy handle to easily connect & disconnect from tractor.
4 lip, metal backed wheel hub seal with purging capabilities
Seals make it harder for water & debris to enter the hub and grease to leave the hub. Metal backing prevents sticks and twine from destroying the seal lips.
Greasable cast steel, continuous hinges
Cast steel hinges make a strong connection & are easy to lubricate.
Center axle options
Single suspension center axle: Spring cushion at the cylinder for cushion with least amount of moving parts. Independent suspension center axle: Offers additional suspension support per wheel axle. Walking tandem center axle: Designed for versatility over a multitude of terrains. Parallel pivot center axis: provides unmatched ground contact for hill-like terrains.
Wing axle option
Solid wing axle: One piece wing axle that attains support from cylinder spring cushion on center axle. Independent suspension wing axle: Offers additional suspension support on wing axle.
Dual-acting fold cylinders (optional)
Allows for a narrow transport width of 7'3" (2.21 m).
Stroke control flip spacers
Easily change cut height with a flip of a spacer.
RC(L)4710 & RCM(L)4710
50 - 250 hp (37.3 - 186.4 kW)
540 rpm or 1000 rpm 250 hp (186.4 kW) Divider and 210 hp (156.6 kW) Center & Wing